GE Profile UltraFast Combo — drain pump filter code 18
GE's own support content for the UltraFast Combo says code 18 means the pump filter needs to be cleaned, and that owners may also notice very wet loads at the end of a wash or dry times running longer than usual.
Mon–Sat, 8am–8pm
- Water, fill and drain
- Drum seal and drain filter cleaning
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 879-5178
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 18
actually means.
GE's own support content for the UltraFast Combo says code 18 means the pump filter needs to be cleaned, and that owners may also notice very wet loads at the end of a wash or dry times running longer than usual.
GE Profile home appliance display
What to do when 18 shows on the home applianceKind of codeWater, fill and drain
Water is arriving too slowly or leaving too slowly, and the cause is usually something that collects over time: a washer drain filter holding lint, coins and hair, a dishwasher sump filter full of food, inlet screens clogged with grit from the supply, or too much detergent leaving suds the machine cannot rinse. Clear the filter over a tray with the machine unplugged, check that the supply valves are fully open, run a cleaning cycle, and book a visit if the hose itself leaks or bulges.
Usually leads toDrum seal and drain filter cleaning
The door boot, drain filter, detergent drawer and fill hoses on the washer cleaned and checked, and the machine leveled.
Shows up asLaundry Taking Two Cycles to Dry: The Lint Path Is Usually Why
Laundry taking two cycles to dry is a load that comes out damp at the end of a normal cycle and needs another run, often with a hotter cabinet and a muggier laundry room.
MakeGE Profile
GE Profile visits often include an Opal nugget ice maker that needs regular cleaning, a refrigerator water filter, and a laundry pair whose lint path has not been checked in years.
SourceGE Profile UltraFast Combo support content
Specific to the GE Profile UltraFast Combo washer-dryer; standard GE Profile washers and dryers do not use this shared-cabinet code.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for 18 on its home appliances. Follow it to the end: the last card says whether this is a visit.
Power down and access the drain pump filter per the Combo's owner's manual.
Remove and rinse the filter clear of lint and debris under running water.
Reinstall the filter fully seated before restoring power and running a cycle.
If wet loads or long dry times continue after cleaning, book a visit rather than repeating the cycle.
Still there?
It usually turns into drum seal and drain filter cleaning. Book with the code and the model number.
What not to do
Code 18 on its own is a cleaning reminder, not a pump or motor failure; it only becomes a repair concern if the same wet-load or long-dry-time symptoms persist after the filter has been properly cleaned.
What you may
notice with it.
The home appliance problems 18 tends to arrive with. Answer these at the home appliance before anyone is booked.
All problems
Where 18 usually leads
Drum seal and drain filter cleaning.
GE Profile
home appliances.
GE Profile visits often include an Opal nugget ice maker that needs regular cleaning, a refrigerator water filter, and a laundry pair whose lint path has not been checked in years.
GE Profile home appliance maintenanceMore GE Profile codes
Water, fill and drain on other makes
Cold storage
Upkeep for everything in the house that keeps things cold: refrigerators, freezers, wine and beverage units and ice makers, cleaned and checked before they start struggling.
Cooking appliances
Upkeep for ovens, ranges, cooktops, hoods, microwaves, steam and speed ovens: burners and igniters cleaned, gas joints checked, grease filters and descaling done on time.
Dish care
Upkeep for dishwashers and disposers: filters rinsed, spray arms cleared, the door seal and drain loop checked, and hard-water scale kept off the parts that heat and spray.
In GE Profile's own words
The pump filter needs to be cleaned. In addition to this fault code, you may find you're getting very wet loads at the end of a wash cycle, or your dry times are longer than they previously were.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Specific to the GE Profile UltraFast Combo washer-dryer; standard GE Profile washers and dryers do not use this shared-cabinet code.
GE Profile 18 home appliance maintenance,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 18.
Can I clear 18 myself?
What does code 18 mean on my GE Profile UltraFast Combo?
Do I need to take the whole unit apart to clean the filter?
What if code 18 keeps coming back right after I clean the filter?
Back to your everyday
Still showing 18?
A booking goes further when it has the reminder or code as shown, the model number from the rating plate, and a word on when that filter, screen or tub was last cleaned. With those three, the office can pack the right filter or cleaner for your appliance.